Precision Machining
- CNC Machining Service
- CNC Milling
- CNC Turning
- Automatic Turning
- Machining Screw/Rivet
- Wire EDM Machining
- Casting & CNC
- Aluminum Profile & CNC
- Cold Heading & CNC
High strength and toughness, fatigue resistant. Alloy steels incorporate additional alloying elements beyond carbon, leading to heightened hardness, toughness, fatigue resistance, and wear resistance
Property Category | Specific Property | Typical Value/Range | Test Conditions/Notes |
---|---|---|---|
Basic Properties | Density | 1.33-1.38 g/cm³ | ASTM D792 |
Water Absorption | 0.1%-0.6% | 24h immersion at 23℃ | |
Light Transmittance | 88%-90% | Visible light range | |
Molding Shrinkage | 1.5%-2.5% | Injection molding | |
Mechanical Properties | Tensile Strength | 50-110 MPa | ASTM D638 |
Elongation at Break | 200%-300% | ASTM D638 | |
Flexural Strength | 90-120 MPa | ASTM D790 | |
Notched Impact Strength | 2-10 kJ/m² | ASTM D256 | |
Thermal Properties | Melting Point | 250-260℃ | ASTM D3418 |
HDT (0.45MPa) | 85-90℃ | ASTM D648 | |
Continuous Service Temp. | ≤120℃ | Long-term use | |
Short-term Heat Resistance | 160℃ | — | |
Electrical Properties | Volume Resistivity | 10¹⁴-10¹⁶ Ω·cm | ASTM D257 |
Dielectric Constant (1MHz) | 3.0-3.3 | ASTM D150 | |
Breakdown Voltage | 20-25 kV/mm | ASTM D149 | |
Environmental Properties | Acid Resistance | Stable | Dilute acids, room temp. |
Alkali Resistance | Poor | Strong bases/high-temp. steam | |
Solvent Resistance | Partial dissolution | Acetone/benzene solvents | |
Flammability Rating | UL94 HB | — |
•Barrier Properties: Light transmittance >88% with medium barrier performance (O₂ permeability: 50-90 cm³·mm/(m²·d·MPa))[6](@ref)
•Enhanced Grades: 30% Glass Fiber Reinforced PET increases HDT to >180°C and flexural strength to 200 MPa[5](@ref)
•Chemical Limitations: Susceptible to hydrolysis in high-temperature steam and alkaline environments[4,5](@ref)
•Packaging: Carbonated drink bottles (pressure-resistant), medical packaging (sterilization-tolerant)[1,3](@ref)
•Electronics: Transformer bobbins, connectors (volume resistivity >10¹⁴ Ω·cm)[2,6](@ref)
•Industrial Parts: Gears, pump housings (superior wear resistance vs. nylon)[5,6](@ref)
•Drying: Mandatory at 120-150°C for 3-4 hours (moisture ≤0.02%)[6](@ref)
•Melt Temperature: 260-290°C (±5°C tolerance)[1](@ref)
•Mold Temperature: 60-80°C to optimize crystallinity (30-40%)[4](@ref)
On December 12 , 2019,LML welcomed three customers again.
Read more about quality assuranceOn December 12 , 2019,LML welcomed three customers again.
Read more about quality assuranceOn December 12 , 2019,LML welcomed three customers again.
Read more about quality assuranceTake advantage of our network and see what LML can do for you